L Repair Tips

Search: L

Results 3937

Make	Model Ch.	Symptom	Problem Solution
Philips	L6 Series	Vertical lines are not straight when picture is very bright or has white text content	Replace resistor 3420 in the beam current circuit 12k or 15k replaced with an 18k
Daewoo	Video Combi Model: GB14F7T1	Smoke came out of vents, then shut down	Small pin hole in line output transformer type FSA36012M
Philips	VR723 LUCY	Power supply LSM-45 would not start up after power failure	Cooling down of the machine during the power outtage triggered the problem: inside the supply module excessive heat is present that causes components to age rapidly, especially those that are located close to the heatsink. Replaced cap. 2116 100nF, 400V
Philips	VR722 LUCY	LSM-45 power supply faulty after power failure	Replaced elco 2112 100µF, 385V and capacitor 2116 100nF, 400V. See also my tip about the philips VR-723 Cooling down during power outtage. Cheers
Toshiba	Video Combi Model: VTV1402S	Dead, or intermittent start up. No voltage supply to line driver	Check R504 270k, feed to switching transistor. Goes high or o/c
Panasonic	ALPHA 2W	Squeal at switch on then goes dead, channel indicator ok	Check the l.o.p transistor Q551 for s/c, overvoltage diode D854 for s/c, R564 / R567 fusible for o/c and also check C808 10uF, 63v and IC801 STR54041M and locally for dry joints
Nokia	SP71D1 and others Stereo Plus	Tv does not start from stand-by. Indicator led blinks quickly	Replace the two smd condensers in parallel between pin 2 of IC NO62 reset line. Remove all of the red glue below the condensers. These condensers must be replaced by new ones of 47nF and 100nF in parallel. IC NO62 TDA8137 sometimes must be also replaced
Matsui	Vid Combi Model: TVR185	Accepts tape then immediately ejects it	The capstan motor was faulty. Fitted new motor
Salora	L	Dead	DN15 s/c 8v line
Seleco	26SA37NL	White line in middle screen, several spikes	Check power switch for arcing, also check 1 ohm resistors on switch board for possible dry joints
Philips	21PT5505/05 L9.1E	The fault with this tv was a snowy picture no channels tuned in also the permanent 33V supply on pin 9 of the tuner was low at only 1.6V	The first thing i tried was a resistance check between pin 9 and ground. The reading was only 120 Ohms. There's a surface mounted cap right next to pin 9 of the tuner. This was found to be leaky, It's value is 47nF. Also resistor 3442 3.9K was o/c
Philips	14PT1352/58 L6.1AA	Sound goes off and no remote control functions when heated	This was found to be due to a faulty micro
Philips	L9.2E	Fuse 1572 blown	Disconnect pin 44 on IC7600, if the fuse stops blowing suspect processor IC7600. It is really expensive, at least in Sweden !
Loewe opta	Profile E3000	White vertical line only displayed on tube	Check for dry joint or burnt track on Horizontal Yoke PCB socket or main board
Panasonic	21LIT	Dead set, only red LED is on	Replace IC AN5606k
Philips	L6.2	Picture is horizontally narrowed and deformed	Capacitor C2913 390nF, 250V on the deflector PCB had lost capacity
Goldstar	CF28A54L PC58A	Lignes horizontaux aut de l'immage après remplacer	IC - TDA8350Q, Condo 470uF, 25V
Finlux	71G2 ID:54361330 Stereo Plus	Bottom half of the screen is black. Very distorted picture in top half. Volume weak. The programming menu, and the "Extra" menu, has disappeared. In "Service mode" Mute, M and TV buttons in sequence, all settings are set to the max. value 63	The existing IC "SPL 40R01" in location NF10, and the connected EEPROM in location NF80, was replaced with replacement IC "SPL 51R02" and an empty EEPROM. It comes in a kit, which also includes installation instructions and a user manual
Philips	28ML8805-16B FL1.6AA	Power supply faults. BUX85F in micro SOPS defective	Change the value of C2260 to 4n7F, replace 7270 with transistor BD825
Philips	28ML8805-16B FL1.6AA	Ticking noise and line in picture	Transistor 7381 BC848C defective when hot